Hp Officejet Pro 8710 Continuous Ink Error

Z7_3054ICK0KGTE30AQO5O3KA30N0

hp-concentra-wrapper-portlet

Actions

HP Inkjet printers - Ink cartridge errors

One of the following errors or messages displays on the printer control panel or the computer, and the printer does not print.

• Cartridge cannot be used until printer is enrolled

• Cartridge error

• Cartridges in wrong slot

• Cartridge Missing

• Cartridge Problem

• Incompatible Cartridge

• Ink Cartridge Failure

• Print cartridge missing or not detected

• Old Generation Cartridge

• Non-HP Chip/Circuitry Detected

Note:

Messages vary based on your printer and firmware version. Check your firmware release notes for your printer for message availability.

Identify your cartridge type for steps to resolve these errors.

Note:

Go to the following documents if you experience these cartridge errors.

• HP Ink Cartridges - 'Use SETUP Cartridges' Error

• HP OfficeJet Printers - 'Incompatible' or 'Defective Cartridge' message (applies to OfficeJet 6810, 6820, 6950, 6960, 8010, 8010e printers, and OfficeJet Pro 6230, 6830, 6960, 6970, 8020, 8020e, 8030, and 8030e printers)

• Non-HP chip or Circuitry Detected message: The indicated cartridges have been blocked by the printer firmware because they contain a non-HP chip or non-HP circuitry. This printer is intended to work only with new or reused cartridges that have new or reused HP chips or circuitry. Replace the indicated cartridges to continue printing. For more information, go to www.hp.com/learn/ds.

• Older Generation Cartridge with HP 902-909 or 952-959 Ink Cartridges: Your printer is a newer-generation printer, which is intended to work exclusively with newer-generation cartridges. See HP Inkjet Supplies - Updated HP 902-909 and 952-959 Ink Cartridges.

Type 1 - HP 21, 22, 27, 28, 56-67, 74, 75, 92-98, 123, 302-305, 652, 653, 667, 680, 682, 803-805, and 901 cartridges - Resolve ink cartridge errors

Resolve errors such as 'Cartridge Missing', 'Depleted Ink Cartridge', and 'Incompatible Cartridge' for printers that use HP 21, 22, 27, 28, 56, 57, 58, 59, 60, 61, 62, 63, 64, 65, 66, 67, 74, 75, 92, 93, 94, 95, 96, 97, 98, 123, 302, 303, 304, 305, 652, 653, 667, 680, 682, 803, 804, 805, and 901 cartridges.

These steps apply to printers with two cartridge slots (black and tri-color). If you do not have a replacement cartridge available and need to print, remove the cartridge indicated in the error message. Acknowledge any prompts to initiate single-cartridge mode, and then try printing. Be sure to complete the following steps before installing any new cartridges.

Perform the following tasks in the order given. Use the printer after each task to see if the issue is resolved.

Check the ink cartridge numbers

Make sure the cartridge model numbers match your printer and country/region.

1. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

2. Look at the cartridge labels.

   • The printer is enrolled in Instant Ink. The cartridges should be marked "Instant Ink". The numbers on Instant Ink cartridges are different from standard cartridges, and Instant Ink cartridges may be larger. Your printer is designed to work with the cartridges shipped to you by HP Instant Ink. If you see Cartridge cannot be used until printer is enrolled messages, use HP's Virtual Agent for quick help, or go to HP Instant Ink support.

   • The printer is NOT enrolled in Instant Ink. Go to the HP Store to make sure that the cartridges are compatible. Your printer must be enrolled in Instant Ink to use Instant Ink cartridges.

3. Replace any incompatible cartridges.

   Note:

   HP+ printers require Original HP cartridges.

Reset the printer

Reset the printer to recover from printer errors or failures.

1. If your printer has a rechargeable battery, remove it.

2. With the printer turned on, disconnect the power cord from the printer.

3. Unplug the power cord from the power source.

4. Wait 60 seconds.

5. Reconnect the power cord to a wall outlet and to the printer.

   Note:

   HP recommends plugging the printer directly into a wall outlet.

6. Turn on the printer to complete the reset.

Clean the ink cartridge and carriage electrical contacts

Remove any debris or buildup from the contacts on the cartridges and in the carriage.

1. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

2. Remove the cartridge indicated in the error message from the carriage.

   • Carriages with cartridge latches: Open the latch, and then pull the cartridge up and out of the slot.

     

   • Carriages without cartridge latches: Gently press down on the cartridge to release it, and then pull it out of the slot.

     

3. Holding the cartridge by the sides, remove any protective tape that still might be on the contacts.

   CAUTION:

   Do not touch the ink nozzles or the copper-colored electrical strip. Touching or trying to remove these parts can result in clogs, ink failure, and bad electrical connections.

   

4. Lightly dampen a lint-free cloth with distilled water, and then wipe the copper-colored contacts on the cartridge.

   

5. Lightly dampen a lint-free cloth or swab with distilled water, and then clean the electrical contacts in the carriage.

   

6. Wait 10 minutes for the contacts to dry, and then reinsert the cartridge into its color-coded slot.

7. Repeat these steps for the other cartridge if it was indicated in the error message.

8. Close the door or lid to the cartridge access area.

   If the error persists, clean the cartridge and carriage contacts a second time.

Replace the problem ink cartridge

Installing a new cartridge can resolve ink-related errors.

1. Obtain a replacement cartridge.

   • Printer is enrolled in Instant Ink. Replacement cartridges are part of your subscription. If you have another Instant Ink cartridge on hand, install it. Otherwise, contact HP Instant Ink support for a new cartridge.

   • Printer is NOT enrolled in Instant Ink. Go to the HP Store or a local retailer to find and purchase compatible supplies. HP recommends genuine HP cartridges.

     Note:

     If you have a defective HP cartridge, it might be under warranty. Go to About Original HP Cartridges for page yield and HP Limited Warranty information.

2. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

3. Remove the cartridge indicated in the error message, and then insert the new cartridge into the slot.

4. Repeat these steps to replace any other cartridges indicated in the error message.

5. Close the door or lid to the cartridge access area, and then follow any instructions to align the printer.

Service the printer

Service or replace your HP product if the issue persists after completing all the preceding steps.

Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area.

To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products.

Type 2 - HP 932, 933, 950, 951-959, 962-969 cartridges - Resolve ink cartridge errors

Resolve errors such as 'Cartridge Missing', 'Depleted Ink Cartridge', and 'Incompatible Cartridge' for printers that use HP 932, 933, 950, 951, 952, 953, 954, 955, 956, 957, 958, 959, 962, 963, 964, 965, 966, 967, 968, and 969 cartridges.

Perform the following tasks in the order given. Use the printer after each task to see if the issue is resolved.

Check the ink cartridge numbers

Make sure the cartridge model numbers match your printer and country/region.

1. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

2. Look at the cartridge labels.

   • The printer is enrolled in Instant Ink. The cartridges should be marked "Instant Ink". The numbers on Instant Ink cartridges are different from standard cartridges, and Instant Ink cartridges may be larger. Your printer is designed to work with the cartridges shipped to you by HP Instant Ink. If you see Cartridge cannot be used until printer is enrolled messages, use HP's Virtual Agent for quick help, or go to HP Instant Ink support.

   • The printer is NOT enrolled in Instant Ink. Go to the HP Store to make sure that the cartridges are compatible. Your printer must be enrolled in Instant Ink to use Instant Ink cartridges.

3. Replace any incompatible cartridges.

   Note:

   HP+ printers require Original HP cartridges.

Reset the printer

Reset the printer to recover from printer errors or failures.

1. If your printer has a rechargeable battery, remove it.

2. With the printer turned on, disconnect the power cord from the printer.

3. Unplug the power cord from the power source.

4. Wait 60 seconds.

5. Reconnect the power cord to a wall outlet and to the printer.

   Note:

   HP recommends plugging the printer directly into a wall outlet.

6. Turn on the printer to complete the reset.

Clean the ink cartridge electrical contacts

Remove any debris or buildup from the contacts on the cartridges.

1. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

2. Push in on the cartridge indicated in the error message to release it from the carriage.

   

3. Wipe the copper-colored contact on the cartridge with a lint-free cloth.

   

4. Slide the cartridge into its color-coded slot until it clicks into place.

5. Repeat these steps for any other cartridges indicated in the error message.

6. Close the door or lid to the cartridge access area.

Replace the problem ink cartridge

Installing a new cartridge can resolve ink-related errors.

1. Obtain a replacement cartridge.

   • Printer is enrolled in Instant Ink. Replacement cartridges are part of your subscription. If you have another Instant Ink cartridge on hand, install it. Otherwise, contact HP Instant Ink support for a new cartridge.

   • Printer is NOT enrolled in Instant Ink. Go to the HP Store or a local retailer to find and purchase compatible supplies. HP recommends genuine HP cartridges.

     Note:

     If you have a defective HP cartridge, it might be under warranty. Go to About Original HP Cartridges for page yield and HP Limited Warranty information.

2. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

3. Remove the cartridge indicated in the error message, and then insert the new cartridge into the slot.

4. Repeat these steps to replace any other cartridges indicated in the error message.

5. Close the door or lid to the cartridge access area, and then follow any instructions to align the printer.

Service the printer

Service or replace your HP product if the issue persists after completing all the preceding steps.

Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area.

To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products.

Type 3 - HP 178, 364, 564, 655, 862, 902-920, 934, 935 cartridges - Resolve ink cartridge errors

Resolve errors such as 'Cartridge Missing', 'Depleted Ink Cartridge', and 'Incompatible Cartridge' for printers that use HP 178, 364, 564, 655, 862, 902, 903, 904, 905, 906, 907, 908, 909, 910, 912, 914, 915, 916, 917, 918, 919, 920, 934, and 935 cartridges.

Perform the following tasks in the order given. Use the printer after each task to see if the issue is resolved.

Check the ink cartridges

Make sure the cartridge model numbers match your printer and country/region, and then check that they are correctly installed.

1. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

2. Look at the cartridge labels.

   • The printer is enrolled in Instant Ink. The cartridges should be marked "Instant Ink". The numbers on Instant Ink cartridges are different from standard cartridges, and Instant Ink cartridges may be larger. Your printer is designed to work with the cartridges shipped to you by HP Instant Ink. If you see Cartridge cannot be used until printer is enrolled messages, use HP's Virtual Agent for quick help, or go to HP Instant Ink support.

   • The printer is NOT enrolled in Instant Ink. Go to the HP Store to make sure that the cartridges are compatible. Your printer must be enrolled in Instant Ink to use Instant Ink cartridges.

3. Replace any incompatible cartridges.

   Note:

   HP+ printers require Original HP cartridges.

4. Make sure the label on the ink cartridge matches the label on the carriage.

   

5. Make sure all the cartridges are firmly seated. If a cartridge is sticking out farther than the others, press it down until it snaps down.

6. If the cartridge does not snap down, gently bend the tab away from the cartridge no more than 1.27 cm (0.5 in), and try again.

   

7. Close the door or lid to the cartridge access area, and then follow any instructions to align the printer if prompted.

Reset the printer

Reset the printer to recover from printer errors or failures.

1. If your printer has a rechargeable battery, remove it.

2. With the printer turned on, disconnect the power cord from the printer.

3. Unplug the power cord from the power source.

4. Wait 60 seconds.

5. Reconnect the power cord to a wall outlet and to the printer.

   Note:

   HP recommends plugging the printer directly into a wall outlet.

6. Turn on the printer to complete the reset.

Clean the ink cartridge and printhead electrical contacts

Remove any debris or buildup from the contacts on the cartridges and in the carriage.

1. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

2. Remove the cartridge indicated in the error message from the carriage.

3. Wipe the copper-colored contact on the cartridge with a lint-free cloth.

   

4. Place the cartridge to the side with the contact facing upwards.

5. Wipe the contact inside the printhead with a lint-free cloth.

   

6. Reinsert the cartridge into its color-coded slot, and then press down on it until it snaps into place.

7. Repeat these steps for any other cartridges indicated in the error message.

8. Close the door or lid to the cartridge access area.

Replace the problem ink cartridge

Installing a new cartridge can resolve ink-related errors.

1. Obtain a replacement cartridge.

   • Printer is enrolled in Instant Ink. Replacement cartridges are part of your subscription. If you have another Instant Ink cartridge on hand, install it. Otherwise, contact HP Instant Ink support for a new cartridge.

   • Printer is NOT enrolled in Instant Ink. Go to the HP Store or a local retailer to find and purchase compatible supplies. HP recommends genuine HP cartridges.

     Note:

     If you have a defective HP cartridge, it might be under warranty. Go to About Original HP Cartridges for page yield and HP Limited Warranty information.

2. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

3. Remove the cartridge indicated in the error message, and then insert the new cartridge into the slot.

4. Repeat these steps to replace any other cartridges indicated in the error message.

5. Close the door or lid to the cartridge access area, and then follow any instructions to align the printer.

Service the printer

Service or replace your HP product if the issue persists after completing all the preceding steps.

Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area.

To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products.

Type 4 - HP 10-13, 18, 38, 39, 70, 72, 73 82, 84, 85, 88, 89, 727, 728, 777, and 940 cartridges - Resolve ink cartridge errors

Resolve cartridge errors for printers that use HP 10, 11, 12, 13, 18, 38, 39, 70, 72, 73, 82, 84, 85, 88, 89, 727, 728, 777, and 940 cartridges.

Perform the following tasks in the order given. Use the printer after each task to see if the issue is resolved.

Check the ink cartridge numbers

Make sure the cartridge model numbers match your printer and country/region.

1. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

2. Look at the cartridge labels.

   • The printer is enrolled in Instant Ink. The cartridges should be marked "Instant Ink". The numbers on Instant Ink cartridges are different from standard cartridges, and Instant Ink cartridges may be larger. Your printer is designed to work with the cartridges shipped to you by HP Instant Ink. If you see Cartridge cannot be used until printer is enrolled messages, use HP's Virtual Agent for quick help, or go to HP Instant Ink support.

   • The printer is NOT enrolled in Instant Ink. Go to the HP Store to make sure that the cartridges are compatible. Your printer must be enrolled in Instant Ink to use Instant Ink cartridges.

3. Replace any incompatible cartridges.

   Note:

   HP+ printers require Original HP cartridges.

Reset the printer

Reset the printer to recover from printer errors or failures.

1. If your printer has a rechargeable battery, remove it.

2. With the printer turned on, disconnect the power cord from the printer.

3. Unplug the power cord from the power source.

4. Wait 60 seconds.

5. Reconnect the power cord to a wall outlet and to the printer.

   Note:

   HP recommends plugging the printer directly into a wall outlet.

6. Turn on the printer to complete the reset.

Remove and reinsert the ink cartridges

Make sure the cartridges are seated properly in the carriage.

1. Open the cartridge access door.

   

2. Pull a cartridge out of its slot.

3. Slide the cartridge back into its color-coded slot until it stops.

   

4. Repeat these steps to remove and reinsert the other cartridges.

5. Close the door to the cartridge access area.

Replace the problem ink cartridge

Installing a new cartridge can resolve ink-related errors.

1. Obtain a replacement cartridge.

   • Printer is enrolled in Instant Ink. Replacement cartridges are part of your subscription. If you have another Instant Ink cartridge on hand, install it. Otherwise, contact HP Instant Ink support for a new cartridge.

   • Printer is NOT enrolled in Instant Ink. Go to the HP Store or a local retailer to find and purchase compatible supplies. HP recommends genuine HP cartridges.

     Note:

     If you have a defective HP cartridge, it might be under warranty. Go to About Original HP Cartridges for page yield and HP Limited Warranty information.

2. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

3. Remove the cartridge indicated in the error message, and then insert the new cartridge into the slot.

4. Repeat these steps to replace any other cartridges indicated in the error message.

5. Close the door or lid to the cartridge access area, and then follow any instructions to align the printer.

Service the printer

Service or replace your HP product if the issue persists after completing all the preceding steps.

Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area.

To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products.

reisingerancentiond.blogspot.com

Source: https://support.hp.com/in-en/document/ish_1721989-1461843-16

Share this post